Your shopping cart is empty or products are not available any more.
0 reviews / Write a review
For years we've seen all sorts of microcontroller-friendly WiFi modules but none of them were really Adafruit-worthy. Either they were too slow, or too difficult to use, or required signing an NDA, or had limited functionality, or too expensive, or too la
The CC3000 hits that sweet spot of usability, price and capability. It uses SPI for communication (not UART!) so you can push data as fast as you want or as slow as you want. It has a proper interrupt system with IRQ pin so you can have asynchronous connections. It supports 802.11b/g, open/WEP/WPA/WPA2 security, TKIP & AES. A built in TCP/IP stack with a "BSD socket" interface. TCP and UDP in both client and server mode, up to 4 concurrent sockets. It does not support "AP" mode, it can connect to an access point but it cannot be an access point.
We carefully wrapped this little silver module into an Arduino shield. We also added a microSD socket and a reset button. It has an onboard 3.3V regulator that can handle the 350mA peak current, and a level shifter to allow 3 or 5V logic level. The antenna layout is identical to TI's suggested layout and we're using the same components, trace arrangement, and antenna so the board maintains its FCC emitter compliance (you'll still need to perform FCC validation for a finished product, but the WiFi part is taken care of). Even though it's got an onboard antenna we were pretty surprised at the range, as good as a smartphone's.
Each order comes with one fully assembled and tested shield, some male header for attaching it to an Arduino and a 2x3 female header that you can use to plug it into the ICSP port of a Mega. We don't have a detailed tutorial yet but to get you started, we've got a fully working Arduino library that is based off of TI's codebase but adapted for use with the AVR. We also have example code showing how to scan the SSID's, connect to your access point and run DHCP, do a DNS lookup to IP address, ping a site and connect to a remote TCP socket such as a website and print out the page.
Please note the hardware is good, but the library code does not yet support all of the CC3000's functionality. At this moment, SSID scanning, connection, DHCP, DNS lookup, ping, and UDP/TCP client & TCP server connections (eg connect to a website and grab data or host a very short website) all work and are tested with example code. Check out our tutorial for wiring and Arduino library downloads
For use with Arduino Uno, Mega, Leonardo/Micro only at this time - we'll try to get the code ported to the Due at some point but no ETA.
Max Dimensions: 68.61mm / 2.7" x 53.38mm / 2.1" x 2.87mm / 0.11"
Using an Apple Airport? Check this thread for details on how to set it up for use with the CC3000
This product is part of the Huzzah family, tested to work with adafruit.io!
This is a blank 13.56MHz RFID/NFC card - often used for train/bus passes but also found in other sys..
This is a blank 13.56MHz RFID/NFC keychain fob - often used for keys but also an easy way to tag som..
This is a blank 13.56MHz RFID/NFC embedded in a phone charm - often used for train/bus passes b..
While this chip has been very popular, its also been very difficult to use. Most of the low cost mod..
KWD 8.75 KWD 7.00
The Bluefruit EZ-Link is a regular 'SPP' serial link client device, that can pair with any computer ..
The Bluefruit LE UART Friend makes it easy to add Bluetooth Low Energy connectivity to anything with..
This is a breakout board from SparkFun for the Silicon Laboratories Si4703 FM tuner chip. Beyond bei..
Build your own cellular project and get off the grid with FONA. This
pack comes with an SMA-antenn..
Give your Ultimate GPS V3 a boost with this external active antenna. This GPS antenna draws about 10..
This tiny micro NFC/RFID tag is super small, and contains an NTAG203 chip plus antenna. It's super t..
S50 chip specification:
1 KiloByte (8 KiloBit) non-volatile EEPROM storage
Built in encrypti..
This little remote control would be handy for controlling a robot or other project from ..
This low cost XBee USB Adapter Board comes in partially assembled kit form and provides a cost-effec..
Make your Internet of Things device cable-free by adding WiFi. Take advantage of the Raspberry Pi an..
This adapter board is designed to make adding wireless point-to-point or mesh networking easy. I lo..
Digi XBee 802.15.4 modules are the easiest-to-use, most reliable and cost-effective RF devices we’ve..
Feather is the new development board from Adafruit, and like its
namesake it is thin, light, and l..
KWD 9.50 KWD 7.00
Ring! Who's that callin'? It's your breadboard! Introducing Adafruit
+ GPS tracking, all in one? Oh yes! Introducing Adafruit FONA 808
The PN532 is the most popular NFC chip, and is what is embedded in pretty much every phone or device..
Brief DescriptionThe ESP8266 WiFi Module is a self contained SOC with integrated
TCP/IP protocol s..
KWD 4.00 KWD 2.50
Cellular + GPS tracking, all in one, for your Arduino? Oh yes! Introducing Adafruit FONA 808 GSM + G..
This latest IR remote control kit is comprised of mini super-thin IR remote control and 38HKz IR rec..
SIM900 GSM/GPRS shield is based on Quad-Band SIM900 GSM/GPRS module. It provides Arduino with GSM/GP..
Brief DescriptionThe ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol sta..
KWD 7.00 KWD 4.50
Introduction This Bluetooth module can easily achieve serial wireless data transmission. Its op..
Introduction Bluetooth transmission module can enable you to get rid of using cable for a seria..
Keyestudio HC-08 Bluetooth module is a new digital transmission module, based on the Bluetooth Speci..
Its good for point-to-point, multipoint and convertible to a mesh network point. We suggest th..
Enter your Email and you will be notified once item will be again available.
We ship to the GCC and MENA regions.
Reliable and fast shipping to your door, quality assured.
Find us on Instagram
Just type @idea_link