Your shopping cart is empty or products are not available any more.
0 reviews / Write a review
This board is a compact (0.4″ × 0.9″) breakout board for ST’s L3GD20H three-axis digital-output gyroscope; we therefore recommend careful reading of the L3GD20H datasheet (3MB pdf) before using this product. The L3GD20H is a great IC, but its small, leadless, LGA package makes it difficult for the typical student or hobbyist to use. It also operates at voltages below 3.6 V, which can make interfacing difficult for microcontrollers operating at 5 V. This carrier board addresses these issues by incorporating additional electronics, including a 3.3 V voltage regulator and level-shifting circuits, while keeping the overall size as compact as possible. The board ships fully populated with its SMD components, including the L3GD20H, as shown in the product picture.
The L3GD20H has many improvements over the older L3GD20, including better accuracy and stability, lower power consumption, and a much shorter start-up time, all in a smaller package that allows the overall carrier board to be smaller. The L3GD20H also offers a wider range of user-selectable output data rates, with lower frequencies available that are more appropriate for human gesture detection, and it features a data enable (DEN) pin that allows readings to be synchronized with external triggers. While the L3GD20H carrier is not a direct drop-in replacement for the L3GD20 carrier due to differences in the pinout and sensor orientation, it should still be usable as a replacement with the appropriate wiring changes, and since the two ICs share the same register structure and I²C device address, code written for one should be easily portable to the other.
The L3GD20H has many configurable options, including three selectable angular rate sensitivities, seven selectable output data rates, seven different embedded FIFO modes for buffering output data, and a programmable external interrupt signal. The three angular velocity readings are available through a digital interface, which can be configured to operate in either I²C or SPI mode.
The carrier board includes a low-dropout linear voltage regulator that provides the 3.3 V required by the L3GD20H, which allows the sensor to be powered from 2.5 V to 5.5 V. The regulator output is available on the VDD pin and can supply almost 150 mA to external devices. The breakout board also includes a circuit that shifts the two I²C lines (or SPI clock and data-in lines) to the same logic voltage level as the supplied VIN, making it simple to interface the board with 5 V systems, and the board’s 0.1″ pin spacing makes it easy to use with standard solderless breadboards and 0.1″ perfboards.
For sensor fusion applications, our MinIMU-9 v3 and AltIMU-10 v4 inertial measurement units combine this L3GD20H with an LSM303D3-axis accelerometer and 3-axis magnetometer on a single board, providing nine independent readings that can be used to calculate an absolute orientation. The AltIMU-10 v4 also includes an LPS25H pressure sensor that can be used to calculate altitude.
Dimensions: 0.4″ × 0.9″ × 0.1″ (13 × 23 × 3 mm)
Weight without header pins: 0.7 g (0.03 oz)
Operating voltage: 2.5 V to 5.5 V
Supply current: ~6 mA
Output format (I²C/SPI): one 16-bit reading per axis
Sensitivity range (configurable): ±245°/s, ±500°/s, or ±2000°/s
A 10×1 strip of 0.1″ straight header pins and a 9×1 strip of 0.1″ right-angle header pins are included, as shown in the picture below. You can solder the header strip of your choice to the board for use with custom cables or solderless breadboards, or you can solder wires directly to the board itself for more compact installations.
The board has one mounting hole that works with #2 and M2 screws (not included).
Using the L3GD20H
Regardless of the interface being used to communicate with the L3GD20H, its VIN pin should be connected to a 2.5 V to 5.5 V source, and GND should be connected to 0 volts. (Alternatively, if you are using the gyro with a 3.3 V system, you can leave VIN disconnected and bypass the built-in regulator by connecting 3.3 V directly to VDD.)
A minimum of two logic connections are necessary to use the L3GD20H in I²C mode (this is the default mode): SCL and SDA. These pins are connected to built-in level-shifters that make them safe to use at voltages over 3.3 V; they should be connected to an I²C bus operating at the same logic level as VIN. The remaining pins are not connected to level-shifters on the board and are not 5V-tolerant, but our 4-channel bidirectional logic level shifter can be used externally with those pins to achieve the same effect.
To use the L3GD20H in SPI mode, four logic connections are typically used: SPC, SDI, SDO, and CS. These should be connected to an SPI bus operating at the same logic level as VIN. The SPI interface operates in 4-wire mode by default, with SDI and SDO on separate pins, but it can be configured to use 3-wire mode so that SDO shares a pin with SDI.
L3GD20H 3-axis gyro carrier with voltage regulator, labeled top view.
L3GD20H 3-axis gyro carrier with voltage regulator in a breadboard.
VIN This is the main power supply connection, and it should be powered at 2.5 V to 5.5 V. The SCL/SPC and SDA/SDI level shifters pull the I²C and SPI bus high bits up to this level.
GND The ground (0 V) connection for your power supply. Your I²C or SPI control source must also share a common ground with this board.
VDD Regulated 3.3 V output. Almost 150 mA is available to power external components. (If you want to bypass the internal regulator, you can instead use this pin as a 3.3 V input with VIN disconnected.)
SCL/SPC Level-shifted I²C/SPI clock line: HIGH is VIN, LOW is 0 V
SDA/SDI Level-shifted I²C data line and SPI data-in line (also doubles as SDO in 3-wire mode): HIGH is VIN, LOW is 0 V
SDO SPI data-out line in 4-wire mode: HIGH is VDD, LOW is 0 V. Also used as a 3.3V-logic-level input to determine I²C slave address (see below). This pin is not level-shifted and is not 5V-tolerant.
CS SPI enable (chip select). Pulled up to VDD to enable I²C communication by default; drive low to begin SPI communication.
DRDY/INT2 Data ready indicator, a 3.3V-logic-level output. HIGH (3.3 V) indicates angular rate data can be read. Can also be configured as a FIFO interrupt. This output is not level-shifted.
INT1 Programmable interrupt, a 3.3V-logic-level output. This output is not level-shifted.
DEN Data enable trigger, a 3.3V-logic-level input. This input is not level-shifted and is not 5V-tolerant.
The above schematic shows the additional components the carrier board incorporates to make the L3GD20H easier to use, including the voltage regulator that allows the board to be powered from a 2.5 V to 5.5 V supply and the level-shifter circuit that allows for I²C and SPI communication at the same logic voltage level as VIN. This schematic is also available as a downloadable PDF (174k PDF).
With the CS pin in its default state (pulled up to VDD), the L3GD20H can be configured and its angular velocity readings can be queried through the I²C bus. Level shifters on the I²C clock (SCL) and data (SDA) lines enable I²C communication with microcontrollers operating at the same voltage as VIN (2.5 V to 5.5 V). A detailed explanation of the I²C interface on the L3GD20H can be found in itsdatasheet (3MB pdf), and more detailed information about I²C in general can be found in NXP’s I²C-bus specification (371k pdf).
In I²C mode, the gyro’s 7-bit slave address has its least significant bit (LSb) determined by the voltage on the SDO pin. The carrier board pulls SDO to VDD through a 4.7 kΩ resistor, making the LSb 1 and setting the slave address to 1101011b by default (this is the same slave address as the L3GD20). If the gyro’s selected slave address happens to conflict with some other device on your I²C bus, you can drive SDO low to set the LSb to 0.
In our tests of the board, we were able to communicate with the chip at clock frequencies up to 400 kHz; higher frequencies might work but were not tested.
To communicate with the L3GD20H in SPI mode, the CS pin (which the board pulls to VDD through a 4.7 kΩ resistor) must be driven low before the start of an SPI command and allowed to return high after the end of the command. Level shifters on the SPI clock (SPC) and data in (SDI) lines enable SPI communication with microcontrollers operating at the same voltage as VIN (2.5 V to 5.5 V).
In the default 4-wire mode, the gyro transmits data to the SPI master on a dedicated data out (SDO) line. If the SPI interface is configured to use 3-wire mode instead, the SDI line doubles as SDO and is driven by the L3GD20H when it transmits data to the master. A detailed explanation of the SPI interface on the L3GD20H can be found in its datasheet (3MB pdf).
We have written a basic Arduino library for the L3G that makes it easy to interface this sensor with an Arduino or Arduino-compatible board like an A-Star. The library makes it simple to configure the L3GD20H and read the raw gyro data through I²C.
The datasheet provides all the information you need to use this sensor, but picking out the important details can take some time. Here are some pointers for communicating with and configuring the L3GD20H that we hope will get you up and running a little bit faster:
The gyro is in power down mode by default. You have to turn it on by writing the appropriate value to the CTRL1 register.
You can read or write multiple registers in a single I²C command by asserting the most significant bit of the register address to enable address auto-increment.
You can enable the same auto-increment feature in SPI mode by asserting the second bit (bit 1, called the MS bit in the datasheet) of an SPI command.
Note: This sensor needs a 4.7K ohm pull-up resistor. Make sure you have one in hand...
Description: This basic piezo sensor from Measurement Specialties is often used for flex, touch..
1: Digital White LED Light Module project2: Piranha LED Light Module3: 3W LED Module4: RGB LED modul..
This pressure transducer has a range of 0 - 10000 PSI (1723.69 kPa) and an a..
This pressure transducer has a range of 0 - 500 PSI (1723.69 kPa) and an accuracy..
We've now got a wider range version of favorite triple-axis accelerometer - it even has an on-board ..
These spring-vibration switches are high sensitivity non-directional vibration induced trigger swit..
Triple-axis analog accelerometer - for measuring motion and tilt
Force sensitive r..
The QTR-3RC reflectance sensor array is intended as a line sensor, but it ca..
Pulse Sensor Amped adds amplification and noise cancellation circuitry to the hardware. It's noticea..
Operating voltage: 2.7 V to 6.2 VAverage current consumption: 5 mA (typical)Output ty..
The GP2Y0A60SZ distance sensor from Sharp offers a wide detection range of 4″ to 60″ (10 cm to ..
Runs on 5V-16V power (if you need to run it off of 3V you can do that by bypassing the regulator, bu..
Detects a wide range of colors and outputs data as 10-bit RGB (Red/Green/Blue) componen..
This compact sonar range finder by Maxbotix detects objects from 0 to 6.45 m (21.2 ft) wit..
Using the MaKey MaKey you can make anything into a key (get it?) just by connecting a few alligator ..
KWD 27.50 KWD 22.00
This board is a compact (0.4″ × 0.9″) breakout board for ST’s LSM6DS33 inertial module, which featur..
These pressures can easily be converted to altitudes. The board has a 3.3 V linear regulator and int..
The Leap Motion Controller is a fascinating new computer sensor that uses multiple cameras and IR li..
This is a pre-wired and waterproofed version of the DS18B20 sensor made with a PTFE wire cable. Hand..
Take your project portable with the included battery pack and stitch it into a final design with con..
Secure your project with biometrics - this all-in-one optical fingerprint sensor will make adding fi..
The Sensor Film Kit is a great new way to make custom-sized sensors out of force sensitive material...
These lightweight brackets are made from 0.8mm-thick aluminum and are specifically designed to work ..
This pressure sensor from Freescale is a great low-cost sensing solution for precision measurement o..
The pre-programmed Touch Board is Arduino-at-Heart, so your Arduino shields and code will work seeml..
Decode nearly any kind of 1D (striped) barcode in your project using this adorable compact barcode s..
An anemometer is a device used for measuring wind speed, and is a common weather station instrument...
This GPS shield works great with either UNO or Leonardo Arduinos and is designed to log data to an S..
It's summer and you're sweating and your hair's all frizzy and all you really want to know is why th..
This current sensor is a carrier board or breakout board for Allegro’s ACS711KLCTR-12AB-T Hall effec..
This current sensor is a carrier board or breakout board for Allegro’s ACS709LLFTR-35BB-T..
The eTape Liquid Level Sensor is a solid-state sensor with a resistive output that varies with the l..
Description: A simple flex sensor 4.5" in length. As the sensor is flexed, the resistance acros..
This board is a compact (0.5″ × 0.9″) breakout board for ST’s L3GD20 three-axis digital-ou..
This current sensor is a carrier board or breakout board for Allegro’s ACS711KLCTR-25AB-T Hall effec..
Put a current meter anywhere with this very handy display. This panel meter requires a DC voltage to..
The Sharp distance sensors are a popular choice for many projects that require accurate di..
This force-sensing resistor (FSR) from Interlink Electronics is a passive component that acts as a v..
This sensor can detect flexing or bending in one direction. They were popularized by being used in t..
These sensors are easy to use, they are basically resistors that change value based on how much thei..
This flammable gas and smoke sensor detects the concentrations of combustible gas in the a..
This methane gas sensor detects the concentration of methane gas in the air and ouputs its ..
New! Version 3 comes with the latest module which has external antenna support and Pulse-Per-Second ..
It is designed to be submersible in water, but it's always best to avoid long-term (over 1 hour at ..
This set includes sensor boards and reflective wheels to add quadrature encoding to two mi..
This Photo Transistor Light Sensor is a simple sensor that detects ambient light. It's kind of the o..
The Pixy CMUCam 5 is an image sensor with a powerful processor that you can program to only send the..
The QTR-3A reflectance sensor array is intended as a line sensor, but it can ..
Operating Voltage: 2.5 V to 5.5 V
Carrier Frequency: 38 kHz
The X-Band Motion Detector operates in the X-band frequency, at 10.525 GHz and indicates detected mo..
These spring-vibration switches are high sensitivity non-directional vibration induced trigger switc..
The "poor man's" accelerometer/motion sensor! These spring-vibration switches are medium sensitivity..
For specific temperature-to-resistance, check the lookup table.
These are often ..
This is a bare wires bead-probe which can measure air or surface temperatures. Most inexpensive the..
The AM2302 is a wired version of the DHT22, in a large plastic body. It is a basic, low-cost digital..
Wide range, low power temperature sensor outputs an analog voltage that is proportional to the ambie..
This current sensor is a carrier board or breakout board for Allegro’s ACS714LLCTR-05B-T Hall effect..
DescriptionThe eTape Liquid Level Sensor is a solid-state sensor with a resistive output that varies..
Description: The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture ..
Description: Piezo elements come in handy when you need to detect vibration or a knock. You can..
Feature:1.Working Voltage : 5V(DC)2.Static current: Less than 2mA..
Description: A simple flex sensor 2.2" in length. As the sensor is flexed, the resistance acros..
This allows a microcontroller with an analog-to-digital converter (ADC), such as an Arduino&nbs..
This breakout board will solve all your current-monitoring problems. Instead of struggling with a mu..
Kit Listing:White LED Module * 1RGB LED Module *13W LED Module &n..
keyestudio XD-58C pulse sensor module is used to measure heart rates. It’s widely applied for studen..
Our water sensor is easy- to-use, portable and cost-effective, it is designed to identify and detect..
keyestudio GUVA-S12SD 3528 Ultraviolet Sensor is used to detect ultraviolet light. It includes GUVA-..
This load sensor, sometimes called a strain gauge, is the same one found in digital bathroom scales ..
This sensor adopts TCS3200 programmable color light-to-frequency converter, it can be applied to col..
The AD8232 is an integrated front end for signal conditioning of cardiac bioelectrical signals to mo..
This cyber-tronic looking sensor hides a secret behind its glimmering eye. Unlike most temperature s..
The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard fo..
Sharp GP2Y1010AU0F onboard, detecting fine particle larger than 0.8μm in diameter, even like the cig..
KWD 13.00 KWD 11.00
Operating voltage: DC 5VQuiescent current: 5mA. Farthest distance: 4.5m.The device is waterproof, bu..
Enter your Email and you will be notified once item will be again available.
We ship to the GCC and MENA regions.
Reliable and fast shipping to your door, quality assured.
Find us on Instagram
Just type @idea_link