Your shopping cart is empty or products are not available any more.
0 reviews / Write a review
The Sensor Film Kit is a great new way to make custom-sized sensors out of force sensitive material. This kit includes one piece of black plastic sensor film (it's thicker and more durable than Velostat but similar in function), two pieces of heavy aluminum foil, and two pieces of clear adhesive polyester film. The sensor film is super durable and changes its electrical resistance when force is applied. It's a lot likeVelostat but a bit more responsive. The aluminum foil is for electrodes and the clear adhesive polyester film is given to keep the sensors together. It's a great way to make a FSR of any size for your microcontroller project.
There's more info on the Sensor Film Kit site including easy instructions on how to make a basic sensor. They also have a bunch of examples of what you can do with the kit.
Note: This sensor needs a 4.7K ohm pull-up resistor. Make sure you have one in hand...
Description: This basic piezo sensor from Measurement Specialties is often used for flex, touch..
This pressure transducer has a range of 0 - 10000 PSI (1723.69 kPa) and an a..
This pressure transducer has a range of 0 - 500 PSI (1723.69 kPa) and an accuracy..
We've now got a wider range version of favorite triple-axis accelerometer - it even has an on-board ..
These spring-vibration switches are high sensitivity non-directional vibration induced trigger swit..
Triple-axis analog accelerometer - for measuring motion and tilt
Force sensitive r..
The QTR-3RC reflectance sensor array is intended as a line sensor, but it ca..
Pulse Sensor Amped adds amplification and noise cancellation circuitry to the hardware. It's noticea..
Operating voltage: 2.7 V to 6.2 VAverage current consumption: 5 mA (typical)Output ty..
The GP2Y0A60SZ distance sensor from Sharp offers a wide detection range of 4″ to 60″ (10 cm to ..
Runs on 5V-16V power (if you need to run it off of 3V you can do that by bypassing the regulator, bu..
Detects a wide range of colors and outputs data as 10-bit RGB (Red/Green/Blue) componen..
This set includes sensor boards and reflective wheels to add quadrature encoding to two mic..
This compact sonar range finder by Maxbotix detects objects from 0 to 6.45 m (21.2 ft) wit..
Using the MaKey MaKey you can make anything into a key (get it?) just by connecting a few alligator ..
These pressures can easily be converted to altitudes. The board has a 3.3 V linear regulator and int..
This board is a compact (0.4″ × 0.9″) breakout board for ST’s L3GD20H three-axis digital-output gyro..
This is a pre-wired and waterproofed version of the DS18B20 sensor made with a PTFE wire cable. Hand..
These lightweight brackets are made from 0.8mm-thick aluminum and are specifically designed to work ..
This pressure sensor from Freescale is a great low-cost sensing solution for precision measurement o..
The pre-programmed Touch Board is Arduino-at-Heart, so your Arduino shields and code will work seeml..
Decode nearly any kind of 1D (striped) barcode in your project using this adorable compact barcode s..
An anemometer is a device used for measuring wind speed, and is a common weather station instrument...
This GPS shield works great with either UNO or Leonardo Arduinos and is designed to log data to an S..
New! Version 3 comes with the latest module which has external antenna support and Pulse-Per-Second ..
It's summer and you're sweating and your hair's all frizzy and all you really want to know is why th..
This current sensor is a carrier board or breakout board for Allegro’s ACS711KLCTR-25AB-T Hall effec..
This current sensor is a carrier board or breakout board for Allegro’s ACS711KLCTR-12AB-T Hall effec..
This current sensor is a carrier board or breakout board for Allegro’s ACS709LLFTR-35BB-T..
The eTape Liquid Level Sensor is a solid-state sensor with a resistive output that varies with the l..
Description: A simple flex sensor 4.5" in length. As the sensor is flexed, the resistance acros..
Take your project portable with the included battery pack and stitch it into a final design with con..
The Leap Motion Controller is a fascinating new computer sensor that uses multiple cameras and IR li..
This board is a compact (0.5″ × 0.9″) breakout board for ST’s L3GD20 three-axis digital-ou..
This board is a compact (0.4″ × 0.9″) breakout board for ST’s LSM6DS33 inertial module, which featur..
Put a current meter anywhere with this very handy display. This panel meter requires a DC voltage to..
The Sharp distance sensors are a popular choice for many projects that require accurate di..
Connect to any microcontroller or system with TTL serial, and send packets of data to take photos, d..
This force-sensing resistor (FSR) from Interlink Electronics is a passive component that acts as a v..
This sensor can detect flexing or bending in one direction. They were popularized by being used in t..
These sensors are easy to use, they are basically resistors that change value based on how much thei..
This flammable gas and smoke sensor detects the concentrations of combustible gas in the a..
This methane gas sensor detects the concentration of methane gas in the air and ouputs its ..
It is designed to be submersible in water, but it's always best to avoid long-term (over 1 hour at ..
This Photo Transistor Light Sensor is a simple sensor that detects ambient light. It's kind of the o..
The Pixy CMUCam 5 is an image sensor with a powerful processor that you can program to only send the..
The QTR-3A reflectance sensor array is intended as a line sensor, but it can ..
Operating Voltage: 2.5 V to 5.5 V
Carrier Frequency: 38 kHz
The X-Band Motion Detector operates in the X-band frequency, at 10.525 GHz and indicates detected mo..
These spring-vibration switches are high sensitivity non-directional vibration induced trigger switc..
The "poor man's" accelerometer/motion sensor! These spring-vibration switches are medium sensitivity..
For specific temperature-to-resistance, check the lookup table.
These are often ..
This is a bare wires bead-probe which can measure air or surface temperatures. Most inexpensive the..
The AM2302 is a wired version of the DHT22, in a large plastic body. It is a basic, low-cost digital..
Wide range, low power temperature sensor outputs an analog voltage that is proportional to the ambie..
DescriptionThe eTape Liquid Level Sensor is a solid-state sensor with a resistive output that varies..
Description: The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture ..
Description: Piezo elements come in handy when you need to detect vibration or a knock. You can..
Feature:1.Working Voltage : 5V(DC)2.Static current: Less than 2mA..
Description: A simple flex sensor 2.2" in length. As the sensor is flexed, the resistance acros..
This allows a microcontroller with an analog-to-digital converter (ADC), such as an Arduino&nbs..
This breakout board will solve all your current-monitoring problems. Instead of struggling with a mu..
Kit Listing:White LED Module * 1RGB LED Module *13W LED Module &n..
keyestudio XD-58C pulse sensor module is used to measure heart rates. It’s widely applied for studen..
Our water sensor is easy- to-use, portable and cost-effective, it is designed to identify and detect..
keyestudio GUVA-S12SD 3528 Ultraviolet Sensor is used to detect ultraviolet light. It includes GUVA-..
This sensor adopts TCS3200 programmable color light-to-frequency converter, it can be applied to col..
The AD8232 is an integrated front end for signal conditioning of cardiac bioelectrical signals to mo..
This cyber-tronic looking sensor hides a secret behind its glimmering eye. Unlike most temperature s..
1: Digital White LED Light Module project2: Piranha LED Light Module3: 3W LED Module4: RGB LED modul..
his pack is designed for people who want to use the new low-cost Adafruit Feather HUZZAH with ESP82..
The ELEV-8 Quadcopter is a flying robotic platform that is lifted and propelled by four fixed rotors..
Want to make your own inventions? Learn circuit-building and programming at the same time with the B..
Harnessing the power of the 8-core Propeller microcontroller is now easier than ever before. The bui..
OWI’s second-generation robotic arm kit, the Robotic Arm Edge, teaches the basic mechanics and elect..
The S2 robot is suitable for a wide range of programming skills. The Scribbler robot arrives pre-pro..
The Boe-Bot Robot takes about 1-2 hours to put together. Each project in the Robotics text provide..
Introduction Arduino super learning kit walks you through the basics of ..
Introduction Keyestudio Arduino super learning kit MEGA is suitable for Arduino enthusiasts. Th..
Enter your Email and you will be notified once item will be again available.
We ship to the GCC and MENA regions.
Reliable and fast shipping to your door, quality assured.
Find us on Instagram
Just type @idea_link