Your shopping cart is empty or products are not available any more.
0 reviews / Write a review
The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of A4988 stepper motor driver carriers, so it can be used as a higher-performance drop-in replacement for those boards in many applications.
The DRV8825 features adjustable current limiting, over-current and over-temperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2-45V and can deliver up to approximately 1.5A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling).
1. Suitable for driving stepper motors within 8.2V~45V 2.5A;
2. Simple step and direction control interface;
3. Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step;
4. Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
5. Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay);
6. Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout;
7. Short-to-ground and shorted-load protection.
This gearmotor is a miniature high-power, 6 V brushed DC motor with a 100.37:1&n..
These boost (step-up) voltage regulators generate higher output
voltages from input volta..
These are good for reverse polarity protection (put it between your DC power jack and circuitry to ..
D24V5Fx regulator family overview
These buck (step-down) voltage regulators generate lower output vo..
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life ca..
This gearmotor is a miniature medium-power, 6 V brushed DC motor with a 51.45:1&..
KWD 0.75 KWD 0.45
These small brushed DC gearmotors can deliver a lot of power for their size. This version has a ..
This 5 V boost (step-up) voltage regulator generates higher output voltages from input vol..
D24V5Fx regulator family overview
These buck (step-down) voltage regulators generate lower output v..
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V ..
These boost (step-up) voltage regulators generate higher output voltages from input voltages as low ..
The compact (0.4″ × 0.5″) D24V5F6 synchronous buck voltage regulator takes an input voltage of up to..
Bring in some muscle to your output pins with 8 mighty Darlingtons! This DIP chip contains 8 drivers..
These boost (step-up) voltage regulators generate higher output voltages from input voltage..
This product is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Dr..
Like our original carrier, the Black Edition offers adjustable current limiting, over-current and ov..
You want to make a cool Arduino robot, maybe a hexapod walker, or maybe just a piece of art with a l..
These are perhaps better known as "the drivers in our assembled Adafruit Motorshield or Motor HAT." ..
Overview The Starter Kit
walks you through the basic..
This kit is following AUM CE362 Course Standards.The Pack Includes the Following Items :
Decode nearly any kind of 1D (striped) barcode in your project using this adorable compact barcode s..
Bare Conductive Paint is a multipurpose electrically conductive material perfect for all of your DIY..
The Pololu basic 2-channel relay carrier modules make it easy to control two single-pole, double-thr..
The included power relay is an Omron G5LE-14-DC5 and is rated for up to 10 A under most conditions...
Good for beginners who want to make stuff move without building a motor controller with feedback & g..
This range makes them perfect for controlling with an Adafruit Motor Shield, or with an Arduino wher..
The driver has a pinout and interface that are nearly identical to those of our A4988 stepper motor..
Texas Instruments’ DRV8835 is a tiny dual H-bridge motor driver IC that can be used for bidirectiona..
Run four solenoids, two DC motors or one bi-polar or uni-polar stepper with up to 600mA per channel ..
For more info checkout the datasheet:
The MAX7219CNG is a compact, serial input/output common-cathode display driver that can interface mi..
As digital devices get smaller and faster, once ubiquitous 5 V logic has given way to ever lower-vol..
This sensor is essentially a reed switch, encased in an ABS plastic shell. Normally the reed is ..
Need to add analog inputs? This chip will add 8 channels of 10-bit analog input to your microcontrol..
Add more power to your robot with this metal-geared servo. The tiny little servo can rotate approxim..
The Micro Maestro is the smallest of Pololu’s second-generation USB servo controllers. The Maestros ..
The Mini Maestros are highly versatile (and compact) servo controllers and general-purpose I/O board..
These small single-pole, double-throw (SPDT) slide switches are rated for 300 mA at 50 VDC and have ..
When you need to amplify, filter, add, or otherwise manipulate analog signals you'll certainly want ..
Power requirements: 4 to 6 VDC* , 15 -200 mA
Communication: Pulse-width modulation
To use, connect one side of the photo cell (either one, its symmetric) to power (for example 5V) and..
KWD 3.00 KWD 2.50
KWD 21.00 KWD 18.00
The Pixy CMUCam 5 is an image sensor with a powerful processor that you can program to only send the..
he HD-3001HB is a great general-purpose, standard-size servo. Two ball bearings help reduce friction..
KWD 5.00 KWD 4.00
Harnessing the power of the 8-core Propeller microcontroller is now easier than ever before. The bui..
The Raspberry Pi 3 is the third generation Raspberry Pi. It replaced
the Raspberry Pi 2 Model B in..
Each LCD features a full color 800 x 480 capacitive touch display that connects to the Pi via an inc..
The Pololu RC switch with Digital Output can be used with standard hobby radio control systems for r..
This RC relay enables easy control of large, electrically isolated loads in radio control (RC) syste..
Description: Resistors are a good thing, in fact, they’re actually crucial in a lot of circuit desig..
KWD 4.75 KWD 3.75
The SN74HC595N is a simple 8-bit shift register IC. Simply put, this shift register is a device that..
The Pololu Simple High-Power Motor Controller makes basic control of brushed DC motors easy, with ou..
This single-pole, double-throw (SPDT) momentary switch can be used as a general-purpose micro switch..
A solid state relay (SSR) allows you to control high-curent AC loads from lower voltage DC control ..
A stepper motor to satisfy all your robotics needs! This 4-wire bipolar stepper has 1.8° per step fo..
Comes with one mount and a bag of hardware for attachment:
4 x 34mm long M4 Pan head
4 x M4 ..
2.5V rated maximum voltage. 630 Farads.
This datasheet covers the DL series, this is the ol..
Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. The..
Great for whenever you need to control medium to high-power electronics such as motors, solenoids, o..
To control with an Arduino, we suggest connecting the orange control wire to pin 9 or 10 and using t..
*BZZZZZZZZZZ* Feel that? That's your little buzzing motor, and for any haptic feedback project you'l..
This module is a compact breakout board for ST’s high-power VNH5019 motor driver IC, a fully integra..
you like to add audio/sound effects to your next project, without an
is a great battery-backed real time clock (RTC) that allows your
Feather is the new development board from Adafruit, and like its
namesake it is thin, light, and l..
KWD 9.50 KWD 7.00
Ring! Who's that callin'? It's your breadboard! Introducing Adafruit
+ GPS tracking, all in one? Oh yes! Introducing Adafruit FONA 808
This RF adapter cable is super handy for anyone doing RF work. Often
times, small electronics save..
incredibly small stereo amplifier is surprisingly powerful - able to
deliver 2 x..
Description: Faster, cheaper, smaller, better, right? The SN754410 Quad Half H-Bridge is just t..
The Photon is a tiny Wi-Fi development kit for
creating connected projects and products for the Int..
Brief DescriptionThe ESP8266 WiFi Module is a self contained SOC with integrated
TCP/IP protocol s..
KWD 4.00 KWD 2.50
This gearmotor is a powerful brushed DC motor with 131.25:1 metal gearbox intended for ope..
Voltage: 12VNo-Load performance: 10,000 RPM, 150mAStall extrapolation: 0.5kg.cm, 5.5A..
The AR-3606HB is a standard-sized servo that has been built by Power
HD specifically for..
KWD 5.25 KWD 4.50
This NEMA 23-size hybrid stepping motor can be used as a unipolar or bipolar stepper motor and has a..
Feature:1.Working Voltage : 5V(DC)2.Static current: Less than 2mA..
IdeaBot is an Arduino based educational robot kit that is designed to give you the best and easiest ..
Introduction Learn Arduino with Idealink StartUP! shield. StartUP! shield provides the fastest, most..
User Safety and Convenience
Bend it. Peel it.
The Most Reliabl..
Description:The bare minimum moving platform that IdeaBot uses. The module includes the following:&n..
This miniature single-pole, double-throw (SPDT) momentary switch can be used as a general-purpose mi..
The HD-1235MG is a giant-scale (also called 1/4-scale or mega-scale) digital servo from Power HD tha..
This allows a microcontroller with an analog-to-digital converter (ADC), such as an Arduino&nbs..
This breakout board will solve all your current-monitoring problems. Instead of struggling with a mu..
Capacitance: 330 uFMaximum Voltage: 35 VHeight: 0.63" (16 mm)Diameter:..
This TI SN754410 motor driver features two H-bridges that can be used
for bidirectional control of ..
These universal aluminum mounting hubs allow you to mount custom wheels and mechanisms to 1/4 i..
This NEMA 17-size hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). E..
KWD 6.50 KWD 5.00
KWD 9.75 KWD 6.75
KWD 6.00 KWD 4.50
If you want to get some sound out of your project but have a tight space
budget, this is a good wa..
Pretty Standard copper-strip board for prototyping and general circuit soldering. 30 Lines with 48 h..
Introduction Arduino super learning kit walks you through the basics of ..
The Arduino Mini 05 is a small microcontroller board originally based on the..
The Arduino Mini 05 is a small microcontroller board originally based on the ATmega168, but now..
Introduction Keyestudio Arduino super learning kit MEGA is suitable for Arduino enthusiasts. Th..
This breakout board for Freescale’s MC33926 full H-bridge has an operating range of 5 V to 28&n..
The FS5103B is a general-purpose, low-cost standard analog servo from FEETECH. Two ball bearings hel..
KWD 4.50 KWD 3.50
The Keyestudio Mega 2560 R3 is an open-source hardware compatible with arduino MEGA 2560 R3.Microcon..
FlashForge Adventurer 3:New generation, smart, lightNozzle: fully upgraded; steady filament loading;..
Kit Listing:White LED Module * 1RGB LED Module *13W LED Module &n..
This is a 2.8 inch TFT LCD touch shield with the drive chip of ILI9325, compatible with Arduino UNO ..
Ethernet expansion board allows Aduino controller connected to the network. It is a built-in WizNet ..
Raspberry Pi 2Pi2Model B+ -Compatible, saving money for HDMI displayThe same size as Pi 3, resolutio..
You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of mo..
This single relay module can be used in interactive projects. This module uses SONGLE 5v high-qualit..
keyestudio XD-58C pulse sensor module is used to measure heart rates. It’s widely applied for studen..
Lots of robot projects need joystick. This module provides an affordable solution. By simply connect..
This is a basic application module. You can simply plug it into an IO shield to have your first tast..
This sensor adopts TCS3200 programmable color light-to-frequency converter, it can be applied to col..
This latest IR remote control kit is comprised of mini super-thin IR remote control and 38HKz IR rec..
Our water sensor is easy- to-use, portable and cost-effective, it is designed to identify and detect..
keyestudio JoyStick Shield adds an nRF24L01 RF interface and Nokia 5110 LCD interface, easy for game..
keyestudio CNC shield V3 is used as driving shield for engraving machines, fully compatible with UNO..
The DS3234 is a low-cost, extremely accurate SPI™ bus real-time clock (RTC) with an integrated tempe..
keyestudio GUVA-S12SD 3528 Ultraviolet Sensor is used to detect ultraviolet light. It includes GUVA-..
1. 5V Omron solid state relays 240V / 2A, output with resistive fuse 240V / 2A.2. Size: 57 * 55 * 23..
Brief DescriptionThe ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol sta..
KWD 7.00 KWD 4.50
keyestudio Uno R3 is a microcontroller board based on the ATmega328. It has 14 digital input/output ..
The AD8232 is an integrated front end for signal conditioning of cardiac bioelectrical signals to mo..
1. 5V Omron solid state relays 240V 2A, output with resistive fuse 240V 2A.2, the input power supply..
keyestudio PRO MICRO is a microcontroller board based on the ATMEGA32U4-MU. It is an easy-to-use ope..
Using this device enables the use of Arduino code in a custom embedded project witho..
5x RED5x YELLOW5x BLUE5x GREEN..
Motor length: 76.4 mmHolding torque: 1.5 N.mAmps: 5.8 ARotor inertia: 380 g.cmMotor weight: 1.1 kgSh..
Model: DHBQ3078APhase number: 3-phaseInput: DC 24-80VCurrent: 2.5-6A..
Product featuresLarge build volume with professional high-quality printingFilament run-out detection..
Flashforge Hunter is an advanced digital light processing (DLP) 3D printer, featuring the latest tec..
The new generation 18 pin PICAXE microcontroller now has parallel tasking, touch sensors and more me..
PICAXE is a neat entry-level microcontroller system that is relatively cheap to get started with. Th..
PICAXE 28 pin microcontroller chip. Enhanced PICAXE28 chips with 8x memory and many additional featu..
This adjustable boost (step-up) voltage regulator generates higher output voltages (between 2 V..
The D24V22Fx family of step-down voltage regulators generates lower output voltages from input volta..
Input voltage: 4 V to 36 V for the version that outputs 3.3 VFixed 3.3 V, 5..
This cyber-tronic looking sensor hides a secret behind its glimmering eye. Unlike most temperature s..
Snap, snap! The Camera v2 is the new official camera board released by the Raspberry Pi Foundation!T..
This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74..
The credit-card-sized computer has become even smaller! The Raspberry Pi Zero W is still the Pi you ..
In the next iteration of the Model B line, Raspberry Pi has given us the very powerful Model B 4 wit..
This dual brushed DC motor driver, based on Freescale’s MC33926 full H-bridge, has a wide operating ..
This tiny breakout board for TI’s DRV8838 motor driver can deliver a continuous 1.7 A (1.8 ..
Introduction This Bluetooth module can easily achieve serial wireless data transmission. Its op..
Introduction Bluetooth transmission module can enable you to get rid of using cable for a seria..
1. Raspberry Pi Camera, supports all Raspberry Pi Boards. 2. Embedded removable IR-CUT fi..
1: Digital White LED Light Module project2: Piranha LED Light Module3: 3W LED Module4: RGB LED modul..
The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard fo..
An adjustable potentiometer can open up many interesting user interfaces. With this rotary potentiom..
This is a 35mm concave momentary push button similar to the ones you find on arcade games. Simple sc..
This is a perfect choice if you are in need of a heavy duty push button! These metal push buttons ar..
This single-pole, double-throw (SPDT) rocker switch makes a great on/off power switch. It is rated f..
Knobs are a great way to finish off your project and make it easier to adjust the level of your deat..
This is a standard 12mm square momentary button. What we really like is the large button head and go..
Operating voltage: DC 5VQuiescent current: 5mA. Farthest distance: 4.5m.The device is waterproof, bu..
The official Raspberry Pi USB-C power supply is here! Super fast with just the right amount of cable..
This load sensor, sometimes called a strain gauge, is the same one found in digital bathroom scales ..
Make you Raspberry Pi 4 seriously cool with the Fan SHIM from Pimoroni! This 30mm no-solde..
This kit includes;1x Raspberry pi 4 (2GB RAM)1x Raspberry pi 4 case1x Raspberry Pi Power Supply..
سوار التعقيم V.2
بالمسؤولية ولمواجهة فايروس كورونا قمنا بتكريس كل امكانياتنا لخدمة ..
KWD 7.00 KWD 6.00
يقدم لكم مركز الكويت للابتكار بالتعاون مع مصنع الصانع للمنتجات الكيماوية
عبوة المعقم ذات التركي..
General brief about the ideaشرح عام عن الفكرةHow to use & refill كيف تستخدمها..
Enter your Email and you will be notified once item will be again available.
We ship to the GCC and MENA regions.
Reliable and fast shipping to your door, quality assured.
Find us on Instagram
Just type @idea_link